Sony lbt zux9 manual

For example, if the memory free space is 1. Up to 32 characters of the name are assigned. XXX is the folder number from to Page 28 Do this Search for a track on an USB device by its folder name and track name and start playback the track. Hold down m or M Find a point in a track on the remote during playback, then release it Press or USB on the remote.

Page Tuner Tuner Listening to the radio You can listen to a radio station either by selecting a preset station, or by manually tuning in the station. Listening to a preset radio station Use buttons on the remote for the operation. Page 32 Listening to a non-preset radio station You can use manual tuning to tune in a station with a weak signal if you know the frequency of the station.

Use buttons on the remote for the operation. Select a tape deck. Load a tape. The recording level is adjusted automatically. Manual Recording: You can record just the portion you want from an audio source, including connected audio components.

If noise is heard while recording from the radio, move the respective antenna to reduce the noise. Page Sound Adjustment Sound Adjustment Adjusting the sound Reinforcing the sound You can reinforce the bass and create a more powerful sound. Page Creating A Party Atmosphere Repeat steps 1 and 2 to adjust the level of other frequency bands and surround effect.

A user equalizer number flashes in the display. Select AQUA 1 create a bubbling effect. Page 41 Using the beat functions With the beat functions, you can enjoy a variety of rhythms. They can be used with any source. Page Selecting The Speaker System Selecting the speaker system You can select the speakers which you want the sound to be output. Page Other Operations Other Operations Using the timer Falling asleep to music — Sleep Timer You can set the system to turn off after a certain time, so that you can fall asleep to music.

The minute display turn-off time changes. The display will show the timer settings. For Recording Timer: The display will show the timer settings. Load a recordable tape into Deck B. Page 45 Turning off the display — Power Saving Mode The demonstration display and the clock display can be turned off to minimize the amount of power consumed during standby mode Power Saving Mode.

Page 48 Note The lighting effect may be different depending on the connected lighting device or the type of music being played back. Page Additional Information Find your problem in the troubleshooting checklist below and take the indicated corrective action. If the problem persists after doing all of the above, consult your nearest Sony dealer. Note that if service personnel changes some parts during repair, these parts may be retained.

Page 50 There is severe hum or noise. The disc tray does not close. Page 52 The folder, track, artist name or volume label do not appear properly. Refer to the USB device operating manual for how to deal with this problem. If the problem persists, contact your nearest Sony dealer.

Page 54 Playback does not start. Playback does not start from the first track. Page 55 The tape does not erase completely.

There is excessive wow or flutter, or the sound drops out. Page 56 Messages One of the following messages may appear or flash in the display during operation. No Tab You cannot record onto the tape because the tab has been removed from the tape. No Tape There is no tape in the tape deck. Page Precautions Protected! The USB device is write-protected.

Push STOP! To Exposed Metal Parts on Set. Notice that the minus side of a tantalum capacitor may be damaged by heat. Do not touch the soldering iron on the same conductor of the circuit board within 3 times.

Be careful not to apply force on the conductor when soldering or unsoldering. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Boards requiring use of unleaded solder are printed with the lead- free mark LF indicating the solder contains no lead. Caution: Some printed circuit boards may not come printed with. Unleaded solder has the following characteristics.

Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time.

Caution: The printed pattern copper foil may peel away if. Strong viscosity Unleaded solder is more viscous sticky, less prone to flow than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc.

During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick- up block.

Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This label is located on the rear exterior. Check leakage as described below.