Xw inverter installation manual

Indicates required information. Thank you for your question. We will do our best to respond in one business day or less. Save on energy costs with utility time of use and demand charge optimization. Schneider considers the XW Pro the heart of your home power system, connecting solar and battery storage with the grid for backup power and energy security. It can be used for solar and storage, or backup power systems without solar and has an innovative, integrated design that minimizes external balance-of-system components allowing for quick and easy installation as either a grid-tie battery backup system or a fully off-grid power system.

Up to 4 inverters can be paralleled for up to Dual AC inputs enable AC generator input as well as grid interaction. An optional automatic generator start AGS unit is also available. A configurable auxiliary relay with an output of mA at 12 VDC is included in each inverter.

Page Connecting The Batteries 2. They must be installed in the positive side of the DC circuit, as close as possible to the battery. A spark is normal when this connection is made. Use a wrench to tighten the bolt to the required torque. Installing a sensor extends battery life by preventing overcharging in warm temperatures and undercharging in cold temperatures. The replacement part number is Residual Current Detection 2— The neutrals are connected to each other, requiring only one neutral connection when the installation uses a Xantrex XW Power Distribution Panel.

Figure AC Equipment Grounding 2—21 This manual for use by qualified personnel only Determine which circuits the inverter will power, and install the appropriate circuit breakers into the inverter panel. Page Ac System Bonding System bonding must be done in one place only to avoid ground loops, and it must be done differently in on-grid and off-grid systems. The AC System Bonding for On-grid input neutral is already bonded to ground by the incoming utility grid system.

Page 42 Actual wiring and grounding requirements may vary. AC Generator Actual wiring and grounding requirements may vary. AC Wiring - Generator. The external switch, if pressed, overrides the control provided from the front panel. Confirm All Connections Once the AC and DC wiring have been installed and connected, go back over all connections and make sure they are secure and have been installed correctly.

Button Button Briefly press the Equalize button and the O button at the same time to enable or disable Invert mode. Figure Enable the Inverter 3.

Apply AC from grid or generator, and then confirm voltage. One of them must be on for the unit to charge. Recharge with external Measure DC voltage Within tolerance?

When installing more than one inverter at a location, a Xantrex XW System Control Panel is required to give each inverter and other Xantrex Xanbus-enabled devices a unique name and to modify the factory-installed default settings to match and support the installation. Page Basic Functional Test-Multiple Inverters Also, if the inverter has been pre-configured, it may go straight into normal operating mode.

Check for faults. If fault conditions exist, correct them and then restart the Functional Test. About This Guide. The Guide provides safety guidelines, detailed planning, and procedures for installing the SW products only, and is not compatible with other Schneider Electric inverter. The purpose of this Owner's Guide is to provide the information and procedures necessary for configuring, operating, maintaining, and troubleshooting the.

This Guide includes information about monitoring and configuring the Conext. The safety alert symbol shall not be used with this type of safety message. Failure to follow these instructions can result in equipment damage. Please Note. Electrical equipment should only be installed, operated, serviced, and maintained by qualified personnel.

No responsibility is assumed by Schneider Electric for any. And finally all the User Guides related to your drive, listed below: You can download these technical publications and other technical information from our website at www. Standards and Terminology. The technical terms, terminology, and the corresponding descriptions in this manual normally use User Manual.

July My Site menu. From the drop-down list, select the Inverters tab. To add an Inverter. Click Add Inverter to add an inverter, in the Inverters screen. The following pop-up window appears. Figure Inverter screen Jul 24, Save this manual for easy access during the installation, maintenance and trouble shooting of the inverter.

Related Information. You can find more information about Schneider Electric Solar, as well as its.